taib

We then have to attach the lid using the shock cord and another clip made from the copper wire.

Cut the shock cord slightly longer than the height of the pot and tie a double knot in one end and thread it through the frisby then the clip and back through the frisby and tie another knot.



Then melt a hole in the other end of the pot placing the hole at 90 degrees to the weights and take another length of shock cord and knotit and thread it up through the pot and through the hole on the lid.
Pull this cord as tight as possible and tie a knot in it and trim it off.



Completed pot.

I burn my name ( Pity I cannot spell it) into the pot with the soldering iron .I also burn my name into the float ( Helps preventing people thinking that they are their pots.)
I have lost a couple of photos where I initially attach the mesh to the frisbee so I will take some more tomorrow night and update.
I did make some pots out of galvanised gutterguard and they were a lot easier to make but they are starting to rust out after only 2 months in NPD, If you can find some 250 mil begonia saucers they are a lot easier to make up and use less gutterguard and catch just as well as the larger frisbee pots.
Happy shrimping.
Cheers
Ray

After several different types I think that I have finally got it right.
What do you need.
Cable ties - Bunnings or cheaper still on ebay.
Plastic gutter guard 180mm wide Bunnings whites super gutter guard 180mm X 8 m about $7 or cheaper at Masters.
Ideally 25mm begonia pot saucers from K mart $1 each but they havent had any for months.so I use Frisbees from K mart $1 each.



Bundle of

tent pole shock cord $3 from K mart
around 12 gauge gi soft drawn fencing wire. I scrounged some from a farmer mate.
Empty 2l soft drink bottled.
I use soft copper wire for the hooks and attaching the tie rope. You should be able to scrounge some from a sparky or auto electrician


First step is to cut the gutterguard to length. Just mark the edge of the frisbee with a felt pen and place a mark on a length of wood and roll the frisbee Add an inch to allow for an overlap join.
Similarly cut the fencing wire to length.
The fencing wire has to be formed into a circle and the neck of a 9kg gas bottle is ideal for the frisbee size and if you are fortunate to find some 25mm begonia saucers an upturned flower pot is good.
Then cut a hole in the frisbee slightly smaller in diameter than the soft drink bottle.

Next step is to cut the neck off the soft drink bottle ( I find scissors best leave the screw top on the bottle and it is easier to make the initial plunge into the bottle}




Then using a small tipped soldering iron melt 4 holes around the hole in the frisbee and corresponding holes in the drink neck and cable tie the neck to the frisbee,( Do this in well ventilated area because of the burning plastic fumes.) You could drill the holes but it is much faster with the soldering iron.
You will note that I have also made holes around the circumference of the frisbee.You only make the holes on one of the frisbees.

Next step is to join 2 lengths of the gutterguard side by side.



Just tie them together loosely untill the whole lengthy is complete and then flip them out and then tighten up the cable ties.

The co joined gutterguard is then cabletied to the frisbee and the top is pulled in so that the diameter is slightly smalletr then the outher end that is secured to the frisbee and one of bthe fencing wire circles is cable tied to the top

nAnd then the second wire circle is tied in to the centre of the pot



I then insert a short rod into the top of the trap to attact the clop that I tie the rope to.



Clip is made from the copper wire mentioned earlier.

I then place some weight opposite the rope attach point. ( Anything heavy to take the pot to the bottom quickly.( I use old galvanised bolts )

Next step is to burn 3 holes in the other frisby that is going to be the other end of the pot.